1. Anleitungen
  2. Marken
  3. Bosch Anleitungen
  4. Elektrowerkzeuge
  5. PTK 14 EDT
  6. Originalbetriebsanleitung

Bosch PTK 14 EDT Originalbetriebsanleitung Seite 11

Vorschau ausblenden

Werbung

Inhaltsverzeichnis
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Tacker head
2 Selector switch for DuoTac-Automatic
3 Handle
4 Trigger
5 Thumbwheel for hammer-force preselection
6 Magazine release button
7 Refill indicator
8 Staple strip*
9 Magazine
10 Nail strip*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Tacker
Article number
Impact rate
Intermittent operation (S2)
Fastener
– Staple strip
– Width
– Length
Fastener
– Nail strip
– Length
Magazine capacity, max.
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-16.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
and uncertainty K determined ac-
h
cording to EN 60745:
2
2
a
=7,5 m/s
, K=1,5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
Bosch Power Tools
PTK 14 EDT
0 603 265 5..
-1
min
min
Type 53
mm
mm
mm
Type 48
mm
kg
.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-16.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
30
10
Robert Bosch GmbH, Power Tools Division
11,4
70764 Leinfelden-Echterdingen, GERMANY
6 –14
Leinfelden, 30.06.2014
Assembly
14
Loading the Magazine (see figures A1
100
 Before any work on the machine itself, pull the mains
1,1
plug.
 Use only original Bosch accessories. The precision parts
/II
of the power tool, such as the magazine, the striker and the
shot duct, are matched to Bosch staples and nails. Other
manufacturers use other steel qualities and sizes.
– Turn the power tool around.
– Press release buttons 6 and pull out the magazine 9 toward
the rear.
– Insert the staple strip 8 or the nail strip 10. Hold the tacker
at a slight angle when inserting the nail strip 10, so that the
nails face against the sidewall.
– Insert the magazine 9 again until it engages.
 Do not exert any force when opening, loading and in-
serting the magazine.
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
English | 11
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
A2)
–
1 609 929 Y49 | (27.6.14)
Show quick links

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

  Andere Handbücher für Bosch PTK 14 EDT

Bosch PTK 14 EDT Originalbetriebsanleitung
Bosch PTK 14 EDT Originalbetriebsanleitung 67 Seiten
Bosch PTK 14 EDT Originalbetriebsanleitung
Bosch PTK 14 EDT Originalbetriebsanleitung 9 Seiten

  Verwandte Anleitungen für Bosch PTK 14 EDT

  Verwandte Produkte für Bosch PTK 14 EDT

Inhaltsverzeichnis